• Mail

Chromedecu.org

  • Register
  • Log In
  • Home
  • Getting Started
  • Shop
  • Ecus
  • Software
  • Tuning
      • Accell/Decell
      • Active Exhaust
      • Boost Gauge
      • Closed/Open Loop
      • Common Problems
      • Custom Pins Outputs
      • Diagnostics
      • Ecus
      • EGR
      • Fan Control
      • Fuel
      • Fuel Pump
      • Getting Started
      • Idle
      • Intake
      • Knock Check Engine Light
      • Launch Control
      • Lean Spool
      • Limits
      • Limp Mode
      • No Lift to Shift (NLTS)
      • OBD2 Inspection Monitors
      • Peripheries
      • Purge
      • Sensor Scaling
      • Software
      • Start up
      • Timing
      • Turbo
  • Tech How To’s
    • How To’s

      • ECU Installation
      • 3000GT Year and Specification (Fed/Cali) Identification
      • No Lift to Shift (NLTS)
      • Wideband Oxygen Sensor WBO2
      • Radiator Fan Control Conversion for Flash Ecu
  • History
  • Contact
  • Cart - $0.00

    No products in your shopping cart.

No Lift to Shift (NLTS)

You are here: Home » Tuning » No Lift to Shift (NLTS)

No Lift to Shift (NLTS)

 

Clutch in Rev Limit (also called No Lift to Shift or NLTS) will only work with BOTH bit 2 and bit 4 Enabled in Periphery 1. Clutch in Rev Limit also requires a wire be hooked from one of the two clutch switches to pin 67 of the ECU. Instructions for this will be included later.

All this function does is change the rev limiter while the clutch is depressed AND when you have the throttle held to the floor. This function cuts fuel and spark thus making the RPMs drop without the need to lift off the throttle during gear changes.

Depending on which clutch switch you use, you may have to edit the NLTS Clutch Switch Selector value. I recommend people use the Cruise Control Power Kill switch instead of the Starter Switch as the function is enabled as soon as the clutch pedal is pushed down slightly. The cruise switch is also much much easier to get at under the dash.

  • Accell/Decell
  • Active Exhaust
  • Boost Gauge
  • Closed/Open Loop
  • Common Problems
  • Custom Pins Outputs
  • Diagnostics
  • Ecus
  • EGR
  • Fan Control
  • Fuel
  • Fuel Pump
  • Fuel Trims
  • Getting Started
  • Idle
  • Idle – Smoothing Out your Setup
  • Intake
  • Knock Check Engine Light
  • Launch Control
  • Lean Spool
  • Limits
  • Limp Mode
  • No Lift to Shift (NLTS)
  • OBD2 Inspection Monitors
  • Peripheries
  • Purge
  • Sensor Scaling
  • Software
  • Start up
  • Timing
  • Turbo

Recent How To’s

  • 91-93 US VR4/91-98GTO Version 2 Plug and Play Flash Ecu Installation
  • 91-93 US VR4/91-98GTO/91-95 SL Fed Spec Version 3 Plug and Play Flash Ecu Installation
  • Wideband Oxygen Sensor WBO2
  • No Lift to Shift (NLTS)
  • 94-97 US VR4 Plug and Play Flash Ecu Installation

Categories

  • '91 – '93 Modifications
  • '94 – '97 Modifications
  • '98-'99 Modifications
  • Uncategorized
  • Wiring

Need Chromed ECU Help? Post Up!

© Copyright - Chromedecu.org - Replete e-Commerce Theme by Kriesi